AEG 99852G-A Manual de usuario

99852 GGas HobOperating InstructionsGBPERFECT IN FORM AND FUNCTION

10Guarantee ConditionsStandard guarantee conditionsWe, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any p

11Instructions for the InstallerEngineers technical dataBURNER ULTRA-RAPID SEMI-RAPID AUXILIARY(triple crown) (medium) (small)POSITION MAX MIN MAX MIN

12700 mm400 mm400 mm100 mm50 mm50 mm55 mm700 mm400 mm100 mm400 mm50 mm50 mm55 mmCLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOOD ABOV

13InstallationImportantThis hob must be installed by qualified personnel to the relevant British Standards.Any gas installation must be carried out by

14Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the hob is to be installed above

15ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unit with doorProper arrangements must be taken indesigning th

16Fitting the hob to the worktopBefore fitting the hob into the cut out, an adhesive seal must be fitted to the undersideoutside edge of the hob. It i

17Electrical connectionsAny electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accor

18Permanent ConnectionIn the case of a permanent connection, it is necessary that you install a double pole switchbetween the hob and the electricity

19Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

2 Important Safety InformationYou MUST read these warnings carefully before installing or using the hob. Ifyou need assistance, contact our Customer C

20A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale andadjust zero if necessary.— Test leads fro

21Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

22CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flame setting. Todo this, follow the procedure below.1)

23Conversion from Natural Gas to LPGIt is important to note that this model is designed for use with natural gas but can beconverted for use with buta

35686-0201 03/04AEG Hausgeräte GmbHPostfach 1036D-90327 Nürnberghttp://www.aeg.hausgeraete.de© Electrolux plc 2003Grafiche MDM -

3z Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.z Ensure the control knobs are in the ‘OFF’ position when

4This appliance is manufactured according to the following EEC directives:73/23 EEC - 90/683 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC, current edition

51. Hob Top2. Semi-rapid Burners3. Auxiliary Burner4. Ultra-rapid Burner (triple crown)5. Control knobsDescription of the HobINSTALLATIONAny gas insta

6Hob burnersTo light a burner:z Push in the relevant control knob and turn it to maximum position.z Upon ignition, keep the knob pushed down about 5 s

7Maintenance and CleaningBefore any maintenance or cleaning can be carried out, you must DISCONNECT thehob from the electricity supply.The hob is best

8Something Not Working?If the hob is not working correctly, please carry out the following checks before contactingyour local Service Force Centre.

9Service and Spare PartsCustomer CareWhen you contact the Service Centre, they will need the following information:1. Your name, address and post code